cockroach quit

On this page Carat arrow pointing down
As of May 12, 2021, CockroachDB v19.2 is no longer supported. For more details, refer to the Release Support Policy.

This page shows you how to use the cockroach quit command to temporarily stop a node that you plan to restart.

You might do this, for example, during the process of upgrading your cluster's version of CockroachDB or to perform planned maintenance (e.g., upgrading system software).


In other scenarios, such as when downsizing a cluster or reacting to hardware failures, it's best to remove nodes from your cluster entirely. For information about this, see Decommission Nodes.


How it works

When you stop a node, it performs the following steps:

  • Finishes in-flight requests. Note that this is a best effort that times out after the duration specified by the server.shutdown.query_wait cluster setting.
  • Gossips its draining state to the cluster, so that other nodes do not try to distribute query planning to the draining node. Note that this is a best effort that times out after the duration specified by the server.shutdown.drain_wait cluster setting, so other nodes may not receive the gossip info in time.
  • No new ranges are transferred to the draining node, to avoid a possible loss of quorum after the node shuts down.

If the node then stays offline for a certain amount of time (5 minutes by default), the cluster considers the node dead and starts to transfer its range replicas to other nodes as well.

After that, if the node comes back online, its range replicas will determine whether or not they are still valid members of replica groups. If a range replica is still valid and any data in its range has changed, it will receive updates from another replica in the group. If a range replica is no longer valid, it will be removed from the node.

Basic terms:

  • Range: CockroachDB stores all user data and almost all system data in a giant sorted map of key value pairs. This keyspace is divided into "ranges", contiguous chunks of the keyspace, so that every key can always be found in a single range.
  • Range Replica: CockroachDB replicates each range (3 times by default) and stores each replica on a different node.


By default, if a node stays offline for more than 5 minutes, the cluster will consider it dead and will rebalance its data to other nodes. Before temporarily stopping nodes for planned maintenance (e.g., upgrading system software), if you expect any nodes to be offline for longer than 5 minutes, you can prevent the cluster from unnecessarily rebalancing data off the nodes by increasing the server.time_until_store_dead cluster setting to match the estimated maintenance window.

For example, let's say you want to maintain a group of servers, and the nodes running on the servers may be offline for up to 15 minutes as a result. Before shutting down the nodes, you would change the server.time_until_store_dead cluster setting as follows:

> SET CLUSTER SETTING server.time_until_store_dead = '15m0s';

After completing the maintenance work and restarting the nodes, you would then change the setting back to its default:

> RESET CLUSTER SETTING server.time_until_store_dead;

It's also important to ensure that load balancers do not send client traffic to a node about to be shut down, even if it will only be down for a few seconds. If you find that your load balancer's health check is not always recognizing a node as unready before the node shuts down, you can increase the server.shutdown.drain_wait setting, which tells the node to wait in an unready state for the specified duration. For example:

 > SET CLUSTER SETTING server.shutdown.drain_wait = '10s';


Temporarily stop a node:

$ cockroach quit <flags>

View help:

$ cockroach quit --help


The quit command supports the following general-use, client connection, and logging flags.


Flag Description
--decommission If specified, the node will be removed from the cluster instead of temporarily stopped. See Remove Nodes for more details.
--drain-wait Amount of time to wait for the node to drain before stopping the node. See cockroach node drain for more details.

Default: 10m

Client connection

Flag Description
--host The server host and port number to connect to. This can be the address of any node in the cluster.

Default: localhost:26257
The server port to connect to. Note: The port number can also be specified via --host.

Default: 26257
The SQL user that will own the client session.

Default: root
--insecure Use an insecure connection.

Default: false
--certs-dir The path to the certificate directory containing the CA and client certificates and client key.

Default: ${HOME}/.cockroach-certs/
--url A connection URL to use instead of the other arguments.

Default: no URL

See Client Connection Parameters for more details.


By default, the quit command logs errors to stderr.

If you need to troubleshoot this command's behavior, you can change its logging behavior.


Stop a node from the machine where it's running

  1. SSH to the machine where the node is running.

  2. If the node is running in the background and you are using a process manager for automatic restarts, use the process manager to stop the cockroach process without restarting it.

    If the node is running in the background and you are not using a process manager, send a kill signal to the cockroach process, for example:

    $ pkill cockroach

    If the node is running in the foreground, press CTRL-C.

  3. Verify that the cockroach process has stopped:

    $ ps aux | grep cockroach

    Alternately, you can check the node's logs for the message server drained and shutdown completed.

Stop a node from another machine

  1. Install the cockroach binary on a machine separate from the node.

  2. Create a certs directory and copy the CA certificate and the client certificate and key for the root user into the directory.

  3. Run the cockroach quit command without the --decommission flag:

    $ cockroach quit --certs-dir=certs --host=<address of node to stop>
  1. Install the cockroach binary on a machine separate from the node.

  2. Run the cockroach quit command without the --decommission flag:

    $ cockroach quit --insecure --host=<address of node to stop>

See also

Yes No
On this page

Yes No